Vehicles
20 not categorized PORSCHE 964 ENGINE PARTSCan't find what you need? Try browsing the Accessories or Exploded Diagrams!<-- Try narrowing by car using the menu to the left.93010090104EQ High-quality victor reinz replacement gaskets, o-rings and washers to reseal your engine case (short block). Victor reinz has been supplying German auto manufacturers and Porsche for decades. They are a trusted name in gaskets and sealing products. This kit is complete with everything needed and we source this directly in Germany for an added level of quality. Sold individually. 1 set necessary per car. Please note: if you prefer the genuine crankshaft sealing ring, please order part # 99911342641 this also includes the intermediate shaft o-ring, part # 99970731540. Please check the model fitment tab to ensure accurate fitment.
$118.80
Make a selection 96411691101 Eliminate your clutches slipping and chattering with this genuine kit. We only recommend this kit for non-modified cars that are not running any aftermarket upgrades like exhaust, chip tuning or larger displacements, etc. Complete kit consists of: 1 qty. Clutch disc 1 qty. Pressure plate 1 qty. Release bearing 1 qty. Spline lubricant kit weighs 14.1 lbs. (6.4 kg) tech tip: when you are planning to install a new clutch, it is a good idea to replace the clutch release fork and shaft to ensure proper clutch engagement. Our part # FVD116999 we also recommend a new guide tube 95011681306 for proper installation. View/Change Diagram
From $768.04
Make a selection 91150411502 This one-piece seal is furthest from the rear bumper, we recommend replacing this when removing the motor for maintenance. Any of our OEM replacement parts are designed to appear and perform like the originals. We source these parts in Germany to ensure quality, reliability and precise fitment. We recommend replacing both the small and large engine seals, the large is part # 93050417001 sold individually. 1 necessary per car. View/Change Diagram
From $36.00
Make a selection 96410622301 Known as: engine compartment seal View/Change Diagram
$103.60
Make a selection 96410628308 This cover sits upright along the back of the motor nearest the fire wall on the left side. If you are removing the motor for maintenance, be sure to check and replace the engine covers / heat shields as necessary. We recommend replacing the grommet, part 91160640700 at the same time. Sold individually. 1 necessary per car. Please note: small modifications may be necessary between models View/Change Diagram
From $413.60
Make a selection 94410709101 Engine oil caps and the internal seal can suffer from heat and eventually dry out and crack with age. Be sure to inspect the seal regularly and replace if necessary. This part is sourced in Germany to ensure quality, reliability and precise fitment. Sold individually. 1 necessary per car. View/Change Diagram
From $13.00
Make a selection 96455628101 Engine mats are infamous for sagging, cracking and deteriorating with age. The mat is located just above the engine in the engine compartment. Sold individually. 1 necessary per car. If you are installing a new engine dampening mat, it is best to update the retaining caps as well, part # 99904901140, 10 necessary per car. View/Change Diagram
From $73.35
Make a selection GT011 This deck lid is an exact replacement for the stock 1998-1993 964 c2/4 with grill opening for electric wing. No grill included. Weighs a fraction of the factory part. General Fitment911 1989-94
$550.00
Make a selection 96561204902 Known as: wiring harness engine compartment lamp View/Change Diagram
$51.19
Make a selection 96560612601EQ Oxygen or lambda sensors are critical to your engines health. If the sensor is faulty you may experience poor gas mileage, rough idling or engine pinging. High-quality replacement, designed to perform like the original. We source this part in Germany to ensure quality, reliability and precise fitment. Be sure to check the "fits these models" tab to make sure that this will work for your needs. Sold individually. 1 necessary per car.
$111.10
Make a selection 99763220100 Known as: luggage compartment lamp / light / light luggage compartment front and rear / light luggage compartment front / light engine compartment luggage compartment View/Change Diagram
From $8.60
Make a selection FVD116905 Our FVD exclusive line of clutch kits is culmination of Porsche genuine parts, zf sachs race engineering gmbh parts and motorsports parts that have been developed to work together without compromise. They offer a silky smooth release, superb drivability, can handle more torque (315 ft/lbs. / 425 nm max.) than comparable stage 1 type recommendations. We specifically chose a clutch disc with torsion springs that function as a vibration damper between engine and gearbox, in order to give you an effortless release in 1st gear. This kit is suited for daily use and offers a superior driving experience. Clutch kit includes everything needed for installation: 1 qty. Clutch disc 1 qty. Pressure plate 1 qty. Lightweight ...(choose a part on the right to read more) General Fitment911 1994-98911 1989-94
From $2,234.41
Make a selection FVD1169052 Our FVD exclusive line of clutch kits is culmination of Porsche genuine parts, zf sachs race engineering gmbh parts and motorsports parts that have been developed to work together without compromise. They offer a silky smooth release, superb drivability, can handle more torque (350 ft/lbs. / 475 nm max.) than comparable stage 1 type recommendations. We specifically chose a clutch disc with torsion springs that function as a vibration damper between engine and gearbox, in order to give you an effortless release in 1st gear. The disc also contains sintered metal plates that have a higher friction coefficient than plates with organic friction. A sintered disc allows for higher transmittable torque and is more dirt...(choose a part on the right to read more) General Fitment911 1994-98911 1989-94
From $2,322.61
Make a selection NLA70101200 Fram side decal-large. 356's & 912's used three types of oil filters. The mann filter was used for the most part on early 356 (or pre "a") and possibly a few very early a's. This filter is identified by a 10mm bolt. The rest of the cars used either the h-filter (which is identified by a 16mm bolt) or the fram filter (which is identified by a 12mm bolt). Since there are no chassis or engine number breaks which denote the use of these filters, it is best to measure the bolt to identify your filter. Also, h-filter canisters are generally either all silver or silver with a black cover while fram canisters are orange with a black cover. General Fitment356 1950-59356 1960-65
$8.80
Make a selection NLA55198100 Engine compartment insulation kit. Fits 356 coupe. General Fitment356 1950-59356 1960-65
$798.38
Make a selection NLA70100400 H-filter side decal below inlet. 356's & 912's used three types of oil filters. The mann filter was used for the most part on early 356 (or pre "a") and possibly a few very early a's. This filter is identified by a 10mm bolt. The rest of the cars used either the h-filter (which is identified by a 16mm bolt) or the fram filter (which is identified by a 12mm bolt). Since there are no chassis or engine number breaks which denote the use of these filters, it is best to measure the bolt to identify your filter. Also, h-filter canisters are generally either all silver or silver with a black cover while fram canisters are orange with a black cover. General Fitment356 1950-59356 1960-65
$8.80
Make a selection NLA55198106 Engine compartment insulation kit. Fits 356bt6, 356c coupe. General Fitment356 1960-65
$550.00
Make a selection STP207 This dial gauge holder (z block) is needed for accurate adjustment of valves. Made from high grade aluminum with an anodize finish. Comes equipped with a 50mm dial indicator extension pin. Use this holder with the dial gauge (part number rt33038580). Applicable: Porsche model - all air-cooled Porsche engines. General Fitment911 1965-69911 1987-89 911 1984-86 911 1978-83 930 1975-77 911 1974-77 911 1970-73 356 1950-59 356 1960-65 912 1965-69 914 1970-76
$105.55
Make a selection T80800MAN During the 1950's, 60's and 70's, Porsche required each of their dealer service departments to have this tool for tuning carburetor and mechanical fuel injection engines. Porsche realized that this was the only tool which would produce the accuracy required to calibrate air volume with adjustable throttle plates and have the sensitivity to calibrate air bypass screws for nonadjustable throttle plates. If each cylinder doesn't have exactly the same air intake volume, the horsepower produced by each cylinder will vary, causing the loss of power and shortened engine life. This is the only tool that is 100% accurate, and works with all types of Porsche, pmo, and sidedraft/updraft carburetors. General Fitment912 1965-69356 1960-65 356 1950-59 911 1965-69 911 1970-73 914 1970-76
$221.38
Make a selection NLA70101100 Mann oil filter decal set-late (canister has 10mm bolt). 356's & 912's used three types of oil filters. The mann filter was used for the most part on early 356 (or pre "a") and possibly a few very early a's. This filter is identified by a 10mm bolt. The rest of the cars used either the h-filter (which is identified by a 16mm bolt) or the fram filter (which is identified by a 12mm bolt). Since there are no chassis or engine number breaks which denote the use of these filters, it is best to measure the bolt to identify your filter. Also, h-filter canisters are generally either all silver or silver with a black cover while fram canisters are orange with a black cover. General Fitment356 1950-59356 1960-65
$22.87
Make a selection © 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |